For the band with a similar name, see The Ailerons

Ailerons are hinged control surfaces attached to the trailing edge of the wing of a fixed-wing aircraft. The ailerons are used to control the aircraft in roll. The two ailerons are interconnected so that one goes down when the other goes up: the downgoing aileron increases the lift on its wing while the upgoing aileron reduces the lift on the other wing, producing a rolling moment about the aircraft's longitudinal axis. The word aileron is French for "little wing."

An unwanted side-effect of aileron operation is adverse yaw — a yawing moment in the opposite direction to the turn generated by the ailerons. In other words, using the ailerons to roll an aircraft to the right would produce a yawing motion to the left. As the aircraft rolls, adverse yaw is caused primarily by an increase in induced drag on the rising wing, and a decrease in induced drag on the falling wing. One wing is rising in response to increased lift caused by the greater effective camber of the wing and downward-deflected aileron, and the other wing is falling in response to reduced lift caused by the reduced effective camber of the wing and upward-deflected aileron. Increased lift causes increased induced drag, and reduced lift causes reduced induced drag. A secondary contribution to adverse yaw is caused by the wing on the outside of the turn traveling faster than the inside wing and thus the outer wing experiences more parasitic drag than the inner wing. Modern aileron systems have minimal adverse yaw, such that it is barely noticeable in most powered aircraft. This may be accomplished by the use of differential ailerons, which have been rigged such that the downgoing aileron deflects less than the upward-moving one. Frise ailerons achieve the same effect by protruding beneath the wing of an upward-deflected aileron, most often by being hinged slightly behind the leading edge and near the bottom of the surface, with the lower section of the leading edge protruding slightly below the wing's undersurface when the aileron is deflected upwards, increasing drag on that side. Ailerons may also use a combination of these methods.

With ailerons in the neutral position the wing on the outside of the turn develops more lift than the opposite wing due to the variation in airspeed across the wing span, and this tends to cause the aircraft to continue to roll. Once the desired angle of bank (degree of rotation on the longitudinal axis) is obtained, the pilot uses opposite aileron to prevent the aircraft from continuing to roll due to this variation in lift across the wing span. This minor opposite use of the control must be maintained throughout the turn. The pilot also uses a slight amount of rudder in the same direction as the turn to counteract adverse yaw and to produce a "coordinated" turn where the fuselage is parallel to the flight path. A simple gauge on the instrument panel called the inclinometer, also known as "the ball", indicates when this coordination is achieved.

History

Since the need for roll control on aircraft was not as obvious as the need for heading and pitch control, the aileron came into widespread use well after the rudder and elevator. The Wright Brothers used wing warping instead of ailerons for roll control, and initially, their aircraft much better control in the air than aircraft that used movable surfaces; however, as aileron designs were refined, it became clear that they were much more effective and practical for most aircraft.

There are many conflicting claims over who first invented the aileron. In 1868, before the advent of powered aircraft, English inventor M.P.W. Bolton patented the first aileron-type device for lateral control.[1] New Zealander Richard Pearse may have made a powered flight in a monoplane that included small ailerons as early as 1902, but his claims are controversial (and sometimes inconsistent), and even by his own reports, his aircraft were not well controlled. The aircraft 14 Bis by Santos Dumont was modified to add ailerons in late 1906, though it was never full controllable in flight, likely due to its unconventional wing form. Ailerons were also developed independently by the Aerial Experiment Association, headed by Alexander Graham Bell and by Robert Esnault-Pelterie, a French aircraft builder. Henry Farman's ailerons on the Farman III were the first to resemble ailerons on modern aircraft, and have a reasonable claim as the ancestor of the modern aileron.[2] Other claimants include American William Whitney Christmas, who claimed to have invented the aileron in the 1914 patent for what would become the Christmas Bullet (built in 1918),[3] and American Glenn Curtiss, who flew an aileron-controlled aircraft in 1908.

Combination with other control surfaces

• A control surface that combines an aileron and flap is called a flaperon. A single surface on each wing serves both purposes: used as an aileron, the flaperons left and right are actuated differentially; when used as a flap, both flaperons are actuated downwards. When a flaperon is actuated downwards (i.e. used as a flap) there is enough freedom of movement left to be able to still use the aileron function.
• A further form of roll control, common on modern jet transport aircraft, utilises spoilers in conjunction with ailerons. This is called a spoileron.
• In a delta-winged aircraft, the ailerons are combined with the elevators to form an elevon.
• Modern military aircraft may have no ailerons on the wings at all, and combine roll control with an all-moving tailplane. This is a taileron or a rolling tail.

See also

• Flight controls
• Trailing edge

External links

• NASA Glenn Research Center aileron article with Java demo and more pictures