A rolling-element bearing is a bearing which carries a load by placing round elements between the two pieces. The relative motion of the pieces causes the round elements to roll (tumble) with little sliding.

One of the earliest and best-known rolling-element bearings are sets of logs laid on the ground with a large stone block on top. As the stone is pulled, the logs roll along the ground with little sliding friction. As each log comes out the back, it is moved to the front where the block then rolls on to it. You can imitate such a bearing by placing several pens or pencils on a table and placing your hand on top of them. See "bearings" for more on the historical development of bearings.

A rolling-element rotary bearing uses a shaft in a much larger hole, and cylinders called "rollers" tightly fill the space between the shaft and hole. As the shaft turns, each roller acts as the logs in the above example. However, since the bearing is round, the rollers never fall out from under the load.

Rolling-element bearings have the advantage of a good tradeoff between cost, size, weight, carrying capacity, durability, accuracy, friction, and so on. Other bearing designs are often better on one specific attribute, but worse in most other attributes, although fluid bearings can sometimes simultaneously outperform on carrying capacity, durability, accuracy, friction, rotation rate and sometimes cost. Only plain bearings have as wide use as rolling-element bearings.

Design

Typical rolling-element bearings range in size from 10 mm diameter to a few metres diameter, and have load-carrying capacity from a few tens of grams to many thousands of tonnes.

A particularly common kind of rolling-element bearing is the ball bearing. The bearing has inner and outer races and a set of balls. Each race is a ring with a groove where the balls rest. The groove is usually shaped so the ball is a slightly loose fit in the groove. Thus, in principle, the ball contacts each race at a single point. However, a load on an infinitely small point would cause infinitely high contact pressure. In practice, the ball deforms (flattens) slightly where it contacts each race, much as a tire flattens where it touches the road. The race also dents slightly where each ball presses on it. Thus, the contact between ball and race is of finite size and has finite pressure. Note also that the deformed ball and race do not roll entirely smoothly because different parts of the ball are moving at different speeds as it rolls. Thus, there are opposing forces and sliding motions at each ball/race contact. Overall, these cause bearing drag.

Most rolling element bearings use cages to keep the balls separate. This reduces wear and friction, since it avoids the balls rubbing against each other as they roll, and precludes them from jamming. Caged roller bearings were invented by John Harrison in the mid 1700s as part of his work on chronographs.^[1]

Types of bearings

There are many types of rolling-element bearings, each tuned for a specific kind of load and with specific advantages and disadvantages. For example:

Ball bearings

Ball bearings use spheres instead of cylinders. Clever use of surface tension allows balls of high accuracy to be made much more cheaply than comparable cylinders. Ball bearings can support both radial (perpendicular to the shaft) and axial loads (parallel to the shaft). For lightly-loaded bearings, balls offer lower friction than rollers. Ball bearings can operate when the bearing races are misaligned.

Roller bearings

Common roller bearings use cylinders of slightly greater length than diameter. Roller bearings typically have higher radial load capacity than ball bearings, but a low axial capacity and higher friction under axial loads. If the inner and outer races are misaligned, the bearing capacity often drops quickly compared to either a ball bearing or a spherical roller bearing.

Roller bearings are the earliest known type of rolling-element-bearing, dating back to at least 40 BC.

Needle bearing

Needle roller bearings use very long and thin cylinders. Since the rollers are thin, the outside diameter of the bearing is only slightly larger than the hole in the middle. However, the small-diameter rollers must bend sharply where they contact the races, and thus the bearing fatigues relatively quickly.

Tapered roller bearing

Tapered roller bearings use conical rollers that run on conical races. Most roller bearings only take radial loads, but tapered roller bearings support both radial and axial loads, and generally can carry higher loads than ball bearings due to greater contact area. Taper roller bearings are used, for example, as the wheel bearings of most cars, trucks, buses, and so on. The downsides to this bearing is that due to manufacturing complexities, tapered roller bearings are usually more expensive than ball bearings; and additionally under heavy loads the tapered roller is like a wedge and bearing loads tend to try to eject the roller; the force from the collar which keeps the roller in the bearing adds to bearing friction compared to ball bearings.

Spherical roller bearings

• Spherical roller bearings use rollers that are thicker in the middle and thinner at the ends; the race is shaped to match. Spherical roller bearings can thus adjust to support misaligned loads. However, spherical rollers are difficult to produce and thus expensive. And, the bearings have higher friction than a comparable ball bearing since different parts of the spherical rollers run at different speeds on the rounded race and thus there are opposing forces along the bearing/race contact.

Thrust bearing

An axial load is supported by this type, typically to support a vertical shaft against gravitational loads. Spherical, conical or cylindrical rollers are used; and non rolling element bearings such as hydrostatic bearings see some use.

Other types

Most rolling-element bearing designs are for rotating or oscillating loads, but there are also linear bearing designs. A common example is drawer-support hardware. Another example is a bearing for a shaft which moves axially in a hole. Axial-motion bearings often work like the stone-and-log example, with a pathway so rolling elements that fall off the end are pushed around to the other end, and the load rolls on to it. These are called recirculating bearings and were used in automotive steering units before the extensive introduction of the rack and pinion unit.

Bearing failure

Rolling-element bearings often work well in non-ideal conditions, but sometimes minor problems cause bearings to fail quickly and mysteriously. For example, with a stationary (non-rotating) load, small vibrations can gradually press out the lubricant between the races and rollers or balls (False brinelling). Without lubricant the bearing fails, even though it is not rotating and thus is apparently not being used. For these sorts of reasons, much of bearing design is about failure analysis.

There are three usual limits to the lifetime or load capacity of a bearing: abrasion, fatigue and pressure-induced welding. Abrasion is when the surface is eroded by hard contaminants scraping at the bearing materials. Fatigue is when a material breaks after it is repeatedly loaded and released. Where the ball or roller touches the race there is always some deformation, and hence a risk of fatigue. Smaller balls or rollers deform more sharply, and so tend to fatigue faster. Pressure-induced welding is when two metal pieces are pressed together at very high pressure and they become one. Although balls, rollers and races may look smooth, they are microscopically rough. Thus, there are high-pressure spots which push away the bearing lubricant. Sometimes, the resulting metal-to-metal contact welds a microscopic part of the ball or roller to the race. As the bearing continues to rotate, the weld is then torn apart, but it may leave race welded to bearing or bearing welded to race.

Although there are many other apparent causes of bearing failure, most can be reduced to these three. For example, a bearing which is run dry of lubricant fails not because it is "without lubricant", but because lack of lubrication leads to fatigue and welding, and the resulting wear debris can cause abrasion. Similar events occur in false brinelling damage. In high speed applications, the oil flow also reduces the bearing metal temperature by convection. The oil becomes the heat sink for the friction losses generated by the bearing.

Constraints and trade-offs

All parts of a bearing are subject to many design constraints. For example, the inner and outer races are often complex shapes, making them difficult to manufacture. Balls and rollers, though simpler in shape, are small; since they bend sharply where they run on the races, the bearings are prone to fatigue. The loads within a bearing assembly are also affected by the speed of operation: rolling-element bearings may spin over 100,000 rpm, and the principal load in such a bearing may be momentum rather than the applied load. Smaller rolling elements are lighter and thus have less momentum, but smaller elements also bend more sharply where they contact the race, causing them to fail more rapidly from fatigue.

There are also many material issues: a harder material may be more durable against abrasion but more likely to suffer fatigue fracture, so the material varies with the application, and while steel is most common for rolling-element bearings, plastics, glass, and ceramics are all in common use. A small defect (irregularity) in the material is often responsible for bearing failure; one of the biggest improvements in the life of common bearings during the second half of the 1900s was the use of more homogeneous materials, rather than better materials or lubricants (though both were also significant). Lubricant properties vary with temperature and load, so the best lubricant varies with application.

Although bearings tend to wear out with use, designers can make tradeoffs of bearing size and cost versus lifetime. A bearing can last indefinitely -- longer than the rest of the machine -- if it is kept cool, clean, lubricated, is run within the rated load, and if the bearing materials are sufficiently free of microscopic defects. Note that cooling, lubrication, and sealing are thus important parts of the bearing design.

The needed bearing lifetime also varies with the application. For example, Harris reports on an oxygen pump bearing in the U.S. Space Shuttle which could not be adequately isolated from the liquid oxygen being pumped, but all lubricants reacted with the oxygen leading to fires and other failures. The solution was to lubricate the bearing with the oxygen. Although liquid oxygen is a poor lubricant, it was adequate, since the service life of the pump was just a few hours.

The operating environment and service needs are also important design considerations. Some bearing assemblies require routine addition of lubricants, while others are factory sealed, requiring no further maintenance for the life of the mechanical assembly. Although seals are appealing, they increase friction, and a permanently-sealed bearing may have the lubricant contaminated by hard particles, such as steel chips from the race or bearing, sand, or grit that got past the seal. Contamination in the lubricant is abrasive and greatly reduces the operating life of the bearing assembly. Another major cause of bearing failure is the presence of water in the lubrication oil. Online water in oil monitors have recently been introduced in recent years to monitor the effects of both particles and the presence of water in oil and their combined effect.

References

• A standard reference on bearing design: Harris, Tedric A. (2000, 4th edition). Rolling Bearing Analysis. Wiley-Interscience. ISBN 0-471-35457-0. 
• Also: Johannes Brändlein, Paul Eschmann, Ludwig Hasbargen, Karl Weigand (1999, 3rd edition). Ball and Roller Bearings: Theory, Design and Application. Wiley. ISBN 0-471-98452-3. 

See Also

• How ball bearings, races, and cages are manufactured
• A general technical manual 1Mb from FAG here.
• A technical manual on bearing lubrication 0.8Mb here also from FAG.
• A 1.2Mb technical manual on bearing damage identification from FAG here.
• How bearings work at HowStuffWorks.com: http://science.howstuffworks.com/bearing.htm
• SKF, SKF Group is a global supplier of products, solutions and services in the area comprising rolling bearings, seals, mechatronics, services and lubrication systems.
• NSK, NSK is a japanese company global supplier of products, solutions and services in the area comprising rolling bearings,automotive products, mechatronics, services and lubrication systems.
• Schaeffler Group, A manufacturer of rolling element bearings
• FŁT-Kraśnik SA - rolling bearings factory, the largest Polish manufacturer of rolling bearings

External links

• e-learning Online training program from NSK